Research Note · Experiments

空間中的空氣流動

浮力通風靠的是什麼?外部有風時又會怎樣?這份筆記用簡化的瀏覽器流體模擬,檢討「以高度產生溫度差來帶動空氣」的設計構想。

Airflow in space: an early study of stack (buoyancy-driven) ventilation and how outdoor wind changes it, using a simplified in-browser fluid solver.

狀態 Status
初步研究 · Early study
期間 Period
2026-09 ~ 2026-11
資料 Data
示意資料 · Sample data only
工具 Tools
自寫 JS 求解器 · Custom JS solver

研究問題Research questions

設計上常希望利用挑高、天井或通風塔,讓熱空氣往上排、涼空氣從下方補進來。這份研究想釐清四件事:

  1. 浮力通風的驅動機制是什麼,力量有多大?
  2. 室外比室內熱的時候(亞熱帶夏季白天很常見)會發生什麼?
  3. 加入外部風之後,雙層量體加挑空的配置,氣流會怎麼走?
  4. 城市風場模擬在這類檢討裡扮演什麼角色?

We asked what drives stack ventilation and how strong it is, what happens when outdoor air is hotter than indoor air, how wind changes the flow in a two-storey block with an attached void, and when urban wind modelling becomes necessary.

方法Method

手算估算 · Hand calculation

用浮力壓差與開口流量公式估算量級,作為模擬結果的對照。

Standard stack-pressure and orifice-flow equations give the order of magnitude and a check on the simulation.

簡化 3D 模擬 · Simplified 3D simulation

自行撰寫、在瀏覽器執行的流體求解器,用來看氣流路徑與冷熱分層,比較不同開口配置。

A custom browser solver shows flow paths and thermal layering, and compares opening layouts.

ΔP ≈ ρ · g · h · |T_in − T_out| / T_ref Q ≈ Cd · A_eff · √( 2 · g · h · |ΔT| / T_ref ) A_eff = 1 / √( 1/A_low² + 1/A_high² ) h:上下開口中心的垂直距離 · vertical distance between opening centres Cd = 0.6 ρ = 1.16 kg/m³ T_ref:室內外較高的溫度(K)· the warmer temperature
求解器設定 · Solver setup
項目 Item做法 Approach
基礎方法 BasisStable Fluids(Stam, 1999)的不可壓縮流簡化解 · simplified incompressible Navier–Stokes
對流 Advection半拉格朗日法,三線性內插 · semi-Lagrangian with trilinear interpolation
壓力 PressureSOR 疊代解 Poisson 方程,每步 24~28 次(未完全收斂)· SOR, 24–28 iterations per step, not fully converged
浮力 BuoyancyBoussinesq 近似 · Boussinesq approximation
溫度 Temperature以鬆弛方式拉回設定溫度,代表空調或蓄熱,非熱傳計算 · relaxed toward set points, not a heat-transfer model
外部風 Wind邊界固定冪次律剖面,指數 0.2、基準高度 10 m · power-law profile, α = 0.2, reference 10 m
網格 Grid案例一 25 cm、案例二 40 cm · 25 cm (case 1), 40 cm (case 2)
示意資料 · Sample data

案例一:單一高聳量體

4 × 6 m、高 12 m,室內 30 °C、室外 36 °C,上下各一個 1 × 2 m 開口,開口中心高差約 10.4 m,不考慮外部風。

Case 1: a 4 × 6 × 12 m volume, 30 °C inside and 36 °C outside, one 1 × 2 m opening low and one high, about 10.4 m apart, no wind.

示意資料 · Sample data

案例二:雙層量體+東側挑空

東西 6 m × 南北 8 m、兩層各 4 m;東西兩側每層三扇 1.2 × 1.5 m 窗;東牆中央外接 2 × 3 × 8 m 挑空,上下各一開口。西南風 2.5 m/s(10 m 高),室外 30 °C、室內 31 °C。

Case 2: a 6 × 8 m two-storey block (4 m per floor) with three 1.2 × 1.5 m windows per floor on the east and west, and a 2 × 3 × 8 m void attached to the east wall. South-west wind at 2.5 m/s (10 m height).

主要發現Key findings

驅動力是溫差,不是「室內熱」

空氣被開口兩側空氣柱的壓力差推動。誰比較熱,決定了方向;室內外同溫時,就算室內很熱也不會換氣。

Flow is driven by the indoor–outdoor temperature difference. Which side is warmer sets the direction.

外熱內涼會反向,而且量不小

案例一估算約 2.3 Pa、6,100 m³/h、每小時換氣約 21 次,同時帶入約 12 kW 熱量。冷氣從下方流失,熱空氣從上方灌入。

With outdoor air hotter, flow reverses: about 6,100 m³/h and roughly 12 kW of heat gain in case 1 (sample data).

有風時,開口位置比挑空高度重要

案例二屋頂高度風速約 2.4 m/s,動壓約 3.3 Pa;挑空沒有日照增溫時浮力趨近零。這時由風壓主導。

At 2.4 m/s roof-height wind, dynamic pressure (about 3.3 Pa) far exceeds void buoyancy, so wind dominates.

背風側的挑空會變成排風井

西立面正壓、全部進風;東立面負壓、全部排風。挑空在背風側,上下開口都往外排,把東側房間的空氣吸進挑空後帶走。

The leeward void acts as an exhaust shaft, drawing air from the east rooms and venting through both openings.

圖表與示意Figures

煙囪效應的三種狀態 三個剖面:室內較熱時低處進風高處排風;室內較冷時方向相反;室內外同溫時不流動。 室內較熱 低進、高出 · Normal 室內較冷 低出、高進 · Reverse ≈ 室內外同溫 幾乎不流動 · None
圖 1 煙囪效應的三種狀態 封閉房間裡「熱往上、冷往下」只是內部對流;要換氣,必須同時有溫差和上下高差的開口。 Figure 1. Three states of the stack effect. Venting needs both a temperature difference and openings at different heights.
10.4 m
−6 °C
36 °C

反向煙囪效應

浮力壓差 ΔP
–
理論流速 v
–
每 1 m² 有效開口流量
–
圖 2 浮力壓差估算器 示意資料 · Sample data 依第 2 節公式即時計算,預設值為案例一(高差 10.4 m、室內比室外低 6 °C)。浮力壓差與高差成正比,與溫差大致成正比,量級通常只有數 Pa。 Figure 2. Stack pressure estimator using the equations above. Defaults match case 1. Pressures are typically only a few pascals.
案例二平面氣流示意 西南風下,西側窗全部進風,東側外窗排風,中間窗把室內空氣送進東側挑空,挑空開口往外排。 挑空 Void 室內 Interior 6 × 8 m · 1F / 2F 西側 進風 東側 排風 挑空排風 西南風 SW 2.5 m/s N
圖 3 案例二平面氣流示意(1F、2F 方向相同) 示意資料 · Sample data 西立面為正壓面,東立面與挑空位於背風負壓區。中間窗開向挑空,把房間空氣送進挑空後由上下開口排出。 Figure 3. Plan diagram for case 2. West windows take air in; east windows and the void exhaust it.
圖 4 風壓與挑空浮力的量級比較 示意資料 · Sample data 挑空上下開口高差約 6 m。挑空被曬熱 2~8 °C 時,浮力約 0.5~1.8 Pa,只要風速超過約 0.9~1.7 m/s,風的動壓就會超過它。 Figure 4. With a 6 m void heated 2–8 °C above outdoor air, wind above about 0.9–1.7 m/s already exceeds the buoyancy pressure.
表 1 案例二各開口模擬流量(約 32 秒模擬時間)· 示意資料 Sample data
開口群組 Opening group 方向 Direction 流量 Flow (m³/h)
西側 1F 三窗 · West, 1F進風 In≈ 18,500
西側 2F 三窗 · West, 2F進風 In≈ 24,400
東側 1F 外窗 · East, 1F排風 Out≈ 10,800
東側 2F 外窗 · East, 2F排風 Out≈ 11,900
1F → 挑空 · 1F to void流入挑空 To void≈ 4,700
2F → 挑空 · 2F to void流入挑空 To void≈ 6,100
挑空下開口 · Void, low排風 Out≈ 2,600
挑空上開口 · Void, high排風 Out≈ 3,200

粗網格與壓力未完全收斂,進風總量與排風總量相差約三成,流量應視為趨勢與相對比較,絕對值很可能高估。· Inflow and outflow totals differ by about 30% because of the coarse grid; read these as relative trends.

限制與後續Limitations and next steps

模擬限制 · Limitations

  • 沒有紊流模型與明確黏性項,擴散來自數值誤差
  • 網格粗,解析不出邊界層、屋角分離流與開口收縮
  • 風壓係數未經風洞或文獻校正
  • 壓力未完全收斂,質量不守恆
  • 溫度以鬆弛方式設定,不是熱傳計算
  • 四周假設空曠,沒有鄰棟遮擋

No turbulence model, coarse grid, uncalibrated pressure coefficients, incomplete convergence, simplified temperature, open terrain. Suitable for comparing layouts, not for design values or compliance.

設計含意 · Design implications

  • 白天開空調時關閉高開口,或至少不同時開啟上下開口
  • 把煙囪效應留給夜間通風,帶走日間蓄熱
  • 要在白天使用,可讓排氣道受日照加熱,做成太陽能煙囪
  • 排風口要放在負壓區,避免被風頂回去
  • 進風取自遮陰面或較涼處,降低進氣溫度

Close high openings while cooling, use the stack for night purging, consider a solar chimney for daytime use, and keep exhausts in negative-pressure zones.

城市風場的角色 · Role of urban wind

在密集市區,鄰棟遮擋與街道導風會改變開口實際受到的風向、風速與立面風壓;市區常見的無風時段反而是浮力通風的主場;熱島效應與鄰棟設備排熱也會提高進風溫度、削弱溫差。實務上通常分尺度串接:街廓尺度取得局部風場與風壓係數,再交給建築尺度的多區氣流網路計算各房間換氣量,必要時才做室內 CFD。

In dense urban sites, neighbouring buildings change local wind and facade pressures, calm periods make buoyancy more important, and urban heat raises intake temperatures. A practical chain is neighbourhood CFD for local wind and pressure coefficients, then a multizone airflow network, then room-scale CFD only where needed.

建議的分尺度工具 · Suggested tools by scale
尺度 Scale工具舉例 Example tools產出 Output
街廓 NeighbourhoodOpenFOAM、ENVI-met、PALM-4U局部風速風向、立面風壓係數、微氣候溫度
建築 BuildingCONTAM、EnergyPlus AirflowNetwork風壓與浮力共同作用下各房間換氣量
室內 RoomOpenFOAM 等 CFD 軟體細部流場、死角

後續工作 · Next steps

  1. 以多區氣流網路重算案例二,取代粗網格流量
  2. 加入鄰棟量體,比較有無遮擋時挑空的表現
  3. 比較東風、無風加挑空日照增溫、上開口改為屋頂等情境
  4. 以逐時氣象資料統計無風時數與夜間通風可用時數

參考資料 · References

  1. Stam, J. (1999). Stable Fluids. Proceedings of SIGGRAPH 99. doi:10.1145/311535.311548
  2. ASHRAE Handbook — Fundamentals, chapter “Ventilation and Infiltration”(浮力壓差與開口流量公式的一般來源 · general source for stack and orifice equations)
  3. NIST. CONTAM multizone airflow and contaminant transport software. nist.gov
  4. U.S. Department of Energy. EnergyPlus. energyplus.net
  5. OpenFOAM. openfoam.com
  6. PALM model system (incl. PALM-4U). palm.muk.uni-hannover.de
  7. ENVI-met. envi-met.com

本頁所有案例、數值與圖示皆為假設條件下的示意資料,不代表任何實際建築或專案,不可作為設計值或法規檢討依據。· All cases, values and diagrams are sample data under assumed conditions and do not represent any real building or project.